Installation of a yakima RailGrab Roof Rack on a 2011 Honda Odyssey - etrailer.com Video Clips. Duration : 1.28 Mins.
http://www.etrailer.com/roof-2011_Honda_Odyssey.htm 2011 Honda Odyssey we'll be doing testing 0:00:02 of the Yakima Roof Rack System. We'll be using the Yaki...
Solo Rack installation for 2002-2009 VFR800 Video Clips. Duration : 3.30 Mins.
The Solo Rack by Kanadian Ken from the VFR Discussion forum (www.vfrdiscussion.com) is fantastic for anyone who commutes by themselves and uses a Givi topbox. It moves the weight back over the rear wheel rather than behind it, and also results in a tidy looking bike. You can order one of these directly from Ken here www.vfrdiscussion.com
Putco Truck Bed Rails Installation Video Tube. Duration : 1.33 Mins.
See how easy it is to upgrade the hauling capabilities of your pickup with Putco oval truck bed rails. These pickup bed rails feature huge 2.5" by 1.75" tubing and they install just like all Putco bed rails -, without drilling! Check out how easy they are to install and then find a set for your truck at www.realtruck.com Realtruck.com carries all kinds of other Putco truck accessories that would compliment the crossrail truck bed rails perfectly! www.realtruck.com
www.etrailer.com Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information. Today on our 2012 GMC Terrain, we'll be test fitting the Thule AeroBlade Crossroad Roof Rack System using part numbers THARB47 and TH450R. With our roof rack pre-assembled according to the instructions, we're ready to go ahead and fit it to the vehicle. We'll set the front crossbar on top of the factory raised side rails. We'll bring the rubber coated steel strap underneath the side rails and clamp them to each foot. After ensuring the triangles on each foot are pulling directly over the side rails and that our AeroBlade is even with the vehicle, we can go ahead and tighten it down using the included Allen wrench with an inch foot. And that will secure the front crossbar to our vehicle.
www.etrailer.com Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information. Today on this 2001 Ford Escape we are going to install a Thule AeroBlade and Rapid Tracker 2 roof rack system. First we are going to install our Tracker fit kit into the factory side rails of our Escape. We will measure from the front of the track to the front edge of our fit kit on both the driver and passenger side to make sure they are even with each other and then tighten them down. Next we will put the rear fit kits into place but we are going to leave these loose.
www.etrailer.com Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information. Today on this 2011 Nissan Rogue we are going to show you how to install a Thule Crossroad roof rack system. The Thule Crossroad system is designed to attach to vehicles with factory raised side rails like we have on our Rogue. Once we have the crossbars assembled, we can place them on top of our side rails. Make sure that they are spaced evenly on both sides with the side rails so that the crossbars run perpendicular to your vehicle. Once you have the front crossbar in place, you can use the integrated tool on the end cap to tighten them down. The Crossroad feet attach to the factory side rails using a rubber coated steel band. This band will strongly and securely grip your side rails but the rubber coating will help protect them as well. As we tighten down the clamp on the Crossroad foot, it also tightens the crossbar into the foot. We will move back and forth from the driver side to the passenger side to make sure the rack tightens down evenly and we do not lose our positioning.
www.etrailer.com Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information. Alright, today on this 2008 Acura RDX we are going to install roof rack. We will be using parts from Thule and we will be using the following part numbers. First off, we are going to use the Traverse foot pack, this will be part number TH480. And then we are going to be using roof rack bars, THLB58. And then we are going to use a fit kit. And these are actually the parts that actually adapt the roof rack to the roof line of the vehicle itself. That is going to be part number THKIT1550. Alright, we will go ahead and assemble one side. It looks like there is a lot of parts but it is really easy to put together. So let us go ahead and remove the excess parts we need and go ahead and do one side. 0:37 The best way to start off is to pick out one side of the rack that you want to work with. In this case we are going to start with the driver side in the front and we picked out the parts that are in the instructions for this location. And the parts do specify specific numbers. For instance, on the rubber pad here, it has part number 204 and the instructions tell you that this is located on the driver side in the front. You can see it has a really nice thick pad to it. It is about a 1/2 inch here on one side and about 7/8 inch on the other. And you can see how it matches the roof line this way. And then the same thing applies to the metal ...
www.etrailer.com Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information. Today on this 2006 Nissan Quest we are going to be installing a Rhino Rack roof rack part number SXB3. Once the crossbars are assembled we are ready to go ahead and set them up on the factory raised side rails. We will lay the front crossbar on the raised side rails and make sure that it is running perpendicular to the raised side rails and also that it is overhanging evenly on either side of the vehicle. Once we have it positioned where we want it we can go ahead and use the included allen key to begin tightening the rack down. We will move back and forth from the driver side to the passenger side to make sure we tighten the rack down evenly. Once we have both sides of the crossbar tightened down we can install our locking endcaps. Next we will fit the rear crossbar onto the side rails in the same manner.